German AWD
Moderators: Mikewire, Rennwagen1
Re: German AWD
It's the best part of waking up...
-
Rennwagen1
- The Dubfather
- Posts: 4166
- Joined: Nov Mon 06, 2006 5:21 pm
- Vehicles: 84 GTI, 97 GLX, 04 Touareg V6
- Location: ZooTown Represent!
Re: German AWD
Oh, Kenneth! That is quite the question. We have a car audio section just for stuff like that. What sort of parameters are we talking? Car, budget, goals? Maybe check.out that car audio section, so as not to threadjack this one....
Jd3 wrote:Once again I was slangin rocks and pimpin bitches. Got a degree from the streets. Listen to the song regulate by warren g. I wrote it.
Captain Pajama SharkMikeWire wrote:Vanilla Ice > Depeche Mode.
99% Awesome 100% of the time!!
1.8/2.8/3.2 OEM+
You can pay for school, but you can't buy class!
-
kevin286
- In the trunk...
- Posts: 336
- Joined: Jul Sat 05, 2008 10:23 am
- Vehicles: 02 M3, 06 Taco DCSB, 90 240 Wagon
- Location: Moab, UT
- Contact:
Re: German AWD
Shift boot before
It's junk, fake leather and torn
New from a guy making these out of real leather in the UK
Remove the old, it's heat pressed on
All off, left with this. Reuse this part
There's a plastic collar thing that goes on the nipple part of the boot and holds the top of the boot to the shaft. Like how I used "nipple" and "shaft" in the same sentence and kept a straight face?
Needs a little bit of modification because of the Z3 shift rod I'm using. No big deal, just cut a little bit off with a knife.
Marking where the holes for the inner collar piece go.
And all assembled together.
Slip the boot over the shift rod and snap the ring into place in the console then enjoy the upgrade
It's junk, fake leather and torn
New from a guy making these out of real leather in the UK
Remove the old, it's heat pressed on
All off, left with this. Reuse this part
There's a plastic collar thing that goes on the nipple part of the boot and holds the top of the boot to the shaft. Like how I used "nipple" and "shaft" in the same sentence and kept a straight face?
Needs a little bit of modification because of the Z3 shift rod I'm using. No big deal, just cut a little bit off with a knife.
Marking where the holes for the inner collar piece go.
And all assembled together.
Slip the boot over the shift rod and snap the ring into place in the console then enjoy the upgrade
Last edited by kevin286 on Jul Mon 01, 2019 8:37 pm, edited 1 time in total.
-
kevin286
- In the trunk...
- Posts: 336
- Joined: Jul Sat 05, 2008 10:23 am
- Vehicles: 02 M3, 06 Taco DCSB, 90 240 Wagon
- Location: Moab, UT
- Contact:
Re: German AWD
Ooo Lookie what I found on Craigslist
Fella says "yea, I got this from the old manager at the dealership"
took that in a femtosecond
Fella says "yea, I got this from the old manager at the dealership"
took that in a femtosecond
Last edited by kevin286 on Jul Mon 01, 2019 8:38 pm, edited 1 time in total.
-
YASHA7FOLD
- Euro Addict!!!
- Posts: 2092
- Joined: Jun Wed 30, 2010 4:42 pm
- Vehicles: 58 Buggy,65 Baja,69 Beetle, 72 Westy
- Location: Laurel
- Contact:
